At present, China's medical informatization is in the second stage of development. Most medical institutions have initially built their own medical information systems, and the basic computer hardware and network equipment have been basically completed. In the future, hardware facilities will be gradually reduced, except for regular updates of products. On the other hand, with the deepening of medical information construction, more businesses will be included in the information process, and the proportion of software products and services will be greatly increased.
In the next few years, although hardware (including computer hardware and network equipment) still accounts for more than 60% of the total investment in medical IT, it is gradually decreasing. As the medical and health information market matures, the proportion of software and services in total information investment has gradually increased. The growth of software and services comes from the information construction of new institutions, and the other part comes from the upgrading of the information construction of the original medical institutions. A well-established hospital information system usually consists of hundreds of subsystems, involving many areas of expertise. In the future, there will be more applications in electronic medical records, community health care, and a broader range of health management.
With the improvement of the living standards of our people, the expenditures of various health institutions have gradually increased, while at the same time, the proportion of medical information investment in health expenditures has been continuously increasing. According to the data of the “Forecasting and Investment Strategy Planning Analysis Report of the Medical Informatization Industry†issued by the Prospective Industry Research Institute, the proportion of China’s medical informatization investment in total health expenditure of health institutions rose from 0.49% in 2008-2013. 0.69%. However, compared with the proportion of 3%-5% in developed countries, the gap is still large. There is still much room for improvement in China's medical information market. According to the forecast of the Prospective Industry Research Institute, in 2016, the IT expenditure of the medical industry in China accounted for about 0.82% of the total health expenditure of health institutions.
2008-2016 medical industry IT expenditure as a percentage of total health expenditure of health institutions (unit: %)
The "Guiding Opinions on the Pilot Reform of Public Hospitals" issued by the Ministry of Health and other departments pointed out: "The thinking and key tasks of the reform of public hospitals during the period of 2011 and the '12th Five-Year Plan' will give priority to the development of county-level hospitals and deepen the urban and rural counterpart support work. To coordinate the development of urban and rural health undertakings and promote the balanced development of urban and rural medical resources. The National Development and Reform Commission and the Ministry of Health have initiated the construction of a sound rural medical and health service system. It plans to invest 36 billion yuan in three years to support the construction of 2,176 county-level hospitals nationwide. Therefore, the demand for medical information in economically underdeveloped areas is very strong.
From the perspective of the development of demand, hospital information management system, medical technology information management system and public health information management system are different stages of medical information development from basic to advanced.
In the current situation of China, the hospitals at the hospital level are entering the in-depth development period from the universalization period of the basic medical information management system, and gradually building the medical technology information management system; the secondary and lower hospitals are still in the popularization of basic medical information systems. Application period. Image archiving and transmission, inspection information, pathological information, surgical information, electronic medical records and other medical technology systems are currently only in the construction of large-scale tertiary hospitals, and the informationization of the entire hospital system is far from mature. On the other hand, outside the hospital information management system, public health and regional health information management systems are just beginning to integrate social health care resources, connecting medical insurance, community health care services, remote diagnosis, drug management platforms, and health administrations. Public health information systems with related functions such as banks have only begun to be piloted.
The development of typical demand for medical information in China
With the further development of medical reform, the state's investment in the health care industry continues to increase. Because the hospital's own information construction and the establishment of the public health system platform are important means to improve the medical level of the whole industry, optimize the use of medical resources, increase the level of citizen health care, and ultimately improve the health care level of residents and improve the efficiency of national health expenditure. The IT investment in the industry will be significantly higher than the growth rate of the entire IT industry. After years of hardware-based IT investment, the proportion of software and services will increase.
Electric dc motors were the first type widely used, since they could be powered from existing direct-current lighting power distribution systems. A electric Dc Motor's speed can be controlled over a wide range, using either a variable supply voltage or by changing the strength of current in its field windings. Small electric dc motor are used in tools, toys, and appliances. The universal motor can operate on direct current but is a lightweight motor used for portable power tools and appliances. Larger electric dc motor are used in propulsion of electric vehicles, elevator and hoists, or in drives for steel rolling mills.
Areas of application: the electric dc motor rotor part of the armature iron core, armature, commutator, such as equipment, electric dc motor is suitable for most electronic products, such as electric screwdriver, laser, smart home, gas valve, etc
Applications:
Method of use: the best stable in horizontal plane, installed on theelectric dc motor output shaft parts, cannot use a hammer to knock, knock prone to press into the electric dc motor drive, may cause damage to internal components, and cannot be used in the case of blocked.
Operating temperature range:
Electric dc motor should be used at a temperature of -10~60℃.
The figures stated in the catalog specifications are based on use at ordinary room temperature catalog specifications re based on use at ordinary room temperature (approximately20~25℃.
If a electric dc motor is used outside the prescribed temperature range,the grease on the gearhead area will become unable to function normally and the motor will become unable to start.Depending on the temperature conditions ,it may be possible to deal with them by changing the grease of the motor's parts.Please feel free to consult with us about this.
Storage temperature range:
Electric dc motor should be stored ta a temperature of -15~65℃.
In case of storage outside this range,the grease on the gearhead area will become unable to function normally and the motor will become unable to start.
Service life:
The longevity of geared motors is greatly affected by the load conditions , the mode of operation,the environment of use ,etc.Therefore,it is necessary to check the conditions under which the product will actually be used .The following conditions will have a negative effect on longevity.Please consult with us should any of them apply.
â—Use with a load that exceeds the rated torque
â—Frequent starting
â—Momentary reversals of turning direction
â—Impact loads
â—Long-term continuous operation
â—Forced turning using the output shaft
â—Use in which the permitted overhang load or the permitted thrust load is exceeded
â—A pulse drive ,e.g.,a short break,counter electromotive force,PWM control
â—Use of a voltage that is nonstandard as regards the rated voltage
â—Use outside the prescribed temperature or relative-humidity range,or in a special environment.
â—Please consult with us about these or any other conditions of use that may apply,so that we can be sure that you select the most appropriate model.
when it come to volume production,we're a major player as well .each month,we rurn out 600000 units,all of which are compliant with the rohs directive.Have any questions or special needed, please contact us, we have the engineer group and best sales department to service to you Looking forward to your inquiry. Welcome to our factory.
Electric Dc Motor,Mini Electric Motor,12V Electric Motor,Electric Motor Gearbox
Shenzhen Shunchang Motor Co., LTD. , https://www.scgearmotor.com