Not long ago, he sent an article about right-through chassis sharing. For some heat-dissipating options, light-pollution routines were used naturally. At that time, the articles were of interest to review.
After that, with the appearance of a wave of installed stickers, they also read the sharing of value-friends. One of the authors, the author of the @Dial-Up Internet Service wrote in the article, “The small chassis attaches great importance to the air duct, don’t use it for light pollution. Buying a bunch of LED toy fans to come back, inspired by it, and also consulted relevant information, mainly the evaluation of the large data volume of the big God "solid bird", only with the fan ranking we can refer directly to today.
I have also used Zhang Zhang to borrow it again, thanks to the original author.
General chassis fan is mostly 12cm, here we mainly look at the choice of 12cm fan inlet and outlet fan
Some friends will ask why the same fan in and out of the air will be different, and, for example, fans of the wind chaser 12cm in the wind when the Animai high-pressure cyclone above, in the wind when the unexpectedly failed.
This starts with the wind volume and the wind pressure. When the fans are purchased, these two parameters are more common and are valued by everyone. However, these two parameters are inversely proportional, that is, the wind pressure with large wind volume is small. , The wind pressure is small, the specific test can refer to paste it "solid bird" to do the experiment, simply when you choose to enter the wind when you can choose according to the map, such as the high-pressure cyclone type, you can do into the wind can also Out of the air, the ability ranks in the top.
Here is my case. The lower part of the chassis has an air inlet, and there are two air outlets at the top. This will require three fans, and the fans on the cold row will also be replaced. This requires a total of four fans. In the last article, there were valued friends commented that the wind at the top of the air intake at the bottom of the chassis is commonsense physics knowledge. Thanks to @9alex6 here, so according to this idea, list my options:
Into the wind: Annimei
Out wind: chasing wind x2
Water cooling fan: NB
First talk about the reasons, originally intended to enter and exit the wind with 3 high-pressure cyclone has been solved, accidentally discovered that the richest people chasing wind 12cm disassemble version, the line will be slightly shorter, but does not affect the use of economical and affordable, so start 2 out of the wind, the inlet side or An Naiming high pressure cyclone. As for the cold platooning, the beginning is to use the white bat, but according to the evaluation, the white bat, whether it is an advanced version or an old version, has a very general effect. In addition, the bat has a very good value. A lot higher, it is recommended that the chassis is large and the heat dissipation requirements are not too high. Closer to home, the evaluation of the actual bird did not test the data of the fan blowing cold row, according to some of the evaluation of the other gods, the final lock two blowing artifacts, the first thing is to recognize the king blowing, typhoon GT gentle typhoon, the second Is NB's eloop
Come on first to connect
Anaimei High Pressure Cyclone
NB
In the end, it was the blowing knife
The sculpting knife really can't bear to look at it, NB's ability is only slightly lower than that, so in the end it started NB. In addition, the owl is also a good choice for blowing the cold row, that is, the noise is not really NB quiet, there will be a little sound, for the value of ignoring fan noise, friends can fully consider. The air inlet and outlet fan of the chassis can be completely considered according to the rankings. It is really a predecessor planting trees to cool down.
Finally wait until the goods arrive
Replace the top two air outlets
Afterwards, the lower part of the chassis is installed into the air, and when the chassis is purchased, a game is sent to the chassis fan, which is provided with a dust-proof net. This is because the air-supply fan is not installed, so this time it is also used together.
Inside the chassis:
Bottom, dustproof base:
Insert the air filter:
If there is no air filter, it does not matter. There is a magnetic external air filter, which is available in sizes 12 and 14 cm. It can be attached to an iron chassis or installed together with a screw hole to fix the fan.
This will be installed, but there is a problem, the motherboard has 3 sys fan interface, a cpu fan, cpu fan received a water-cooled head, a sys fan was blocked by the video card, leaving 2 ports, in and out of the wind plus 4 fans on the cold exhaust fan are 4pin temperature control fan, in any case is not enough, but fortunately Taobao can buy a fan hub, the keyword fan hub
Buying the simplest on the line, in fact, there is no technical content, is to put the line together.
Connected to the line looks like:
After the cable is connected, the chassis fan is installed, and then the water cooling fan is replaced.
After you are done, check the wiring and turn it on. The data that was observed with the AIDA64 before and after the replacement of the fan was the temperature after entering the Windows after booting.
As the temperature goes on, the light pollution is gone, leaving only the light of the water-cooled head. However, for the small steel cannon, the heat dissipation should still be placed first, everyone thinks.
Well, write it here
The D-subminiature or D-sub is a common type of electrical connector. They are named for their characteristic D-shaped metal shield. When they were introduced, D-subs were among the smallest connectors used on computer systems.
A D-sub contains two or more parallel rows of pins or sockets usually surrounded by a D-shaped metal shield that provides mechanical support, ensures correct orientation, and may screen against electromagnetic interference. The part containing pin contacts is called the male connector or plug, while that containing socket contacts is called the female connector or socket. The socket's shield fits tightly inside the plug's shield. Panel mounted connectors usually have threaded nuts that accept screws on the cable end connector cover that are used for locking the connectors together and offering mechanical strain relief. Occasionally the nuts may be found on a cable end connector if it is expected to connect to another cable end. When screened cables are used, the shields are connected to the overall screens of the cables. This creates an electrically continuous screen covering the whole cable and connector system.
ANTENK offers one of the most comprehensive lines of high reliability D-Subminiature connectors available for military, avionics, space and high reliability industrial applications.
Features of ANTENK D-Subminiature Connectors
- Standard density d-subminiature connectors
- High density d-subminiature connectors, contacts are available as well as several custom and combination versions.
- All d-subminiature connectors may be manufactured with crimp, solder cup, straight PCB and right angle PCB terminations (except solder cup terminations on High Density configurations).
Ragne of of ANTENK D-Subminiature Connectors
Standard Density solder cup, stamped & formed contact D-subminiature connectors
High Density solder cup, stamped & formed contact D-subminiature connectorsStandard Density solder cup,machined contacts D-subminiature connectors
High Density solder cup,machined contacts D-subminiature connectors
crimp & load D-subminiature connectors
IDC D-subminiature connectors
Standard Density vertical mount D-subminiature connectors
High Density vertical mount D-subminiature connectors
Standard Density right angle D-subminiature connectors
High Density right angle D-subminiature connectors
surface mount D-subminiature connectors
Slim D-sub series
D-subminiature connectors stacked D-sub series
D-Subminiature Connectors
ShenZhen Antenk Electronics Co,Ltd , https://www.antenkwire.com